Cisco asr 1001-hx crypto module
Must occur only. Archived from the Preferences and you're that goes to. We may earn.
Indicates the current requested Cisco lOS license level to boot.
| Cisco asr 1001-hx crypto module | Caution Before you continue to install the terminal block ground wires, stop and perform Step 4. You can verify that the power supply module is firmly latched by gently pulling the power supply handle. Licensed ports in Bay 1 use a 10GE port license. Ensure that the chassis ground is connected on the chassis before you begin installing the DC power supply. Shut Port0-One license is released, Port1 is in unshut state and no units of license is consumed. Unshut Port1-No license would be requested Unshut Port0-One unit of license would be requested When license is released for OC3 SPA, consider that all the ports are unshut Only one unit of license is consumed When 2 ports are shut, one unit of license is released. |
| Betting shop documentary films | 779 |
| Storing data in ethereum | 640 |
| Cisco asr 1001-hx crypto module | 820 |
| Political betting republican nomination polls | However, you must verify the polarity by measuring the voltage between the DC cable leads. Replace the ground lug with cable in the following order: Wire terminal Screw with captive washer Step 6 Tighten the M3 Screw with captive washer to recommended torque of 5 in-lbs for the positive stud and wire. The Flash memory stick can be inserted only in one way, and can be inserted or removed regardless of whether more info router is powered up or not. Before you begin, read these important notices: The color coding of the DC input power supply leads depends on the color coding of the DC power source at your site. Step 2 Insert the power supply module into the appropriate slot smaking sure that the retention latch is firmly placed. Step 2 Ensure that the chassis power switch is in the Standby position. |
All bonus codes for fox bet with
Something how to earn bitcoins fast and easy 2021 honda casually
USD TO MYR INVESTING IN SILVER
Procedure Ensure that the chassis power switch on the chassis is in the Standby position. Step 2 Insert the power supply module into the appropriate slot s , making sure that the retention latch is firmly placed.
You can verify that the power supply module is firmly latched by gently pulling the power supply handle. Step 3 Insert the power supply cables firmly into the power supplies. Note Ensure that both power supplies are inserted firmly and the power cords are in place.
Step 4 If you have changed the chassis power switch to the Standby position in Step 1, press the power switch to the On position. The power supply LEDs are illuminated green. Procedure Turn off the circuit breaker from the power source. Step 2 Ensure that the chassis power switch is in the Standby position. Step 3 Remove the plastic cover from the terminal block.
Step 4 Unscrew the two terminal block screws on the unit and remove the wires from the power supply. Step 5 Press the power supply retaining latch towards the pull handle, grasp the handle with one hand, and pull the power supply out of the slot while supporting the weight of the power supply with the other hand.
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Note Do not install the power supplies with the chassis cover off. This section describes how to install the DC power supply input power leads to the DC input power supply. Before you begin, read these important notices: The color coding of the DC input power supply leads depends on the color coding of the DC power source at your site.
Ensure that the chassis ground is connected on the chassis before you begin installing the DC power supply. Follow the steps provided in the " Chassis Ground Connection " section. These cables are available from any commercial cable vendor. All DC input power cables for the chassis should be 10 gauge wire and cable lengths should match within 10 percent of deviation. In some cases, the DC cable leads are labeled, which is a relatively safe indication of the polarity. However, you must verify the polarity by measuring the voltage between the DC cable leads.
Figure 5. Therefore, before installing the DC cable lugs, be sure to insulate the lugs according to the manufacturer's instructions. Step 4 If you have changed the chassis power switch to the Standby position in Step 1, press the power switch to the On position.
The power supply LEDs are illuminated green. Procedure Turn off the circuit breaker from the power source. Step 2 Ensure that the chassis power switch is in the Standby position. Step 3 Remove the plastic cover from the terminal block. Step 4 Unscrew the two terminal block screws on the unit and remove the wires from the power supply.
Step 5 Press the power supply retaining latch towards the pull handle, grasp the handle with one hand, and pull the power supply out of the slot while supporting the weight of the power supply with the other hand. Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Note Do not install the power supplies with the chassis cover off. This section describes how to install the DC power supply input power leads to the DC input power supply. Before you begin, read these important notices: The color coding of the DC input power supply leads depends on the color coding of the DC power source at your site.
Ensure that the chassis ground is connected on the chassis before you begin installing the DC power supply. Follow the steps provided in the " Chassis Ground Connection " section. These cables are available from any commercial cable vendor. All DC input power cables for the chassis should be 10 gauge wire and cable lengths should match within 10 percent of deviation.
In some cases, the DC cable leads are labeled, which is a relatively safe indication of the polarity. However, you must verify the polarity by measuring the voltage between the DC cable leads. Figure 5. Therefore, before installing the DC cable lugs, be sure to insulate the lugs according to the manufacturer's instructions.
Wiring the DC Input Power Source Warning To reduce risk of electric shock, when installing or replacing the unit, the ground connection must always be made first and disconnected last. Note It is not required to place the power switch in the Standby position if you want to hot-swap a single power supply. Caution Before you continue to install the terminal block ground wires, stop and perform Step 4. Step 4 To prevent any contact with metal lead on the ground wire and the plastic cover, you must wrap the positive and negative lead cables with sleeving.
Insulate the lug with shrink sleeving for each lead wire if using non-insulated crimp terminals.